To Remove Magazine Plug - Mossberg 930 935 - 'S Guns

July 5, 2024, 9:15 am

Steps to disassemble the Mossberg 500/590 series shotgun. Keep your finger off the trigger until your sights are on the target. First, unscrew the bolt release, then pull the bolt assembly out of the receiver. F. Once all shotshells have been removed, physically and visually check the magazine tube to ensure there is no ammunition left in the magazine. Now it's time to remove the barrel from the receiver. REMEMBER the four rules of gun safety: - All guns are always loaded. Grasp the barrel and forearm to prevent them from sliding forward. Pull rearward on the forearm. Tips and tricks for disassembling and cleaning your shotgun. "Woe to you, Oh Earth and Sea, for the Devil sends the beast with wrath, because he knows the time is short... Let him who hath understanding reckon the number of the beast for it is a human number, its number is Six hundred and sixty six. It fits into the hole on the right side of the receiver.

  1. Mossberg 500 magazine tube removal
  2. Magazine tube extension for mossberg 500
  3. Mossberg 500 magazine removal
  4. Mossberg 500 magazine tube removal company
  5. Mossberg 500 magazine plug removal
  6. Mossberg 500 magazine tube removal instructions
  7. Mossberg 500 magazine tube removal services

Mossberg 500 Magazine Tube Removal

I know sometimes there's loctite on the threads and some heat will help, I'm reluctant to do it because I don't have a replacement follower and don't want to do any damage. I have a 90s era Mossberg 500 that I bought as new old stock around 2007. You may want to try this method just in case it helps you. Point the muzzle downward and shake the shotgun in an up and down motion until the wooden dowel falls through the opening at the end of the magazine tube. All wrong, hold the mag tube in the vise. TFB FIELD STRIP: MOSSBERG 500 SHOTGUNS. Or is there a local gunsmith willing to help me out? Do not place your hand over the muzzle at any time.

Magazine Tube Extension For Mossberg 500

Just pull it out and point the magazine tube down and the follower will fall out. Unscrew and remove the magazine cap (Figure 9). Unscrew these screws and remove the trigger assembly. I rarely shoot that particular shotgun, it just sits ready for home defense loaded in my room. To do this, first remove the stock from the receiver. Plus facilitates recurring maintenance. Then, remove the magazine cap and slide the forend forward to expose the magazine tube. Unscrew the Takedown Screw (or magazine cap for similar models) at the end of the magazine. This will eject a shotshell that is in the chamber. Rotate the trigger assembly out from the rear by pulling on the trigger guard. The final step is to remove the magazine tube from the receiver.

Mossberg 500 Magazine Removal

I've tried heating it up. Then, unscrew the magazine tube nut, which is located at the front of the receiver. Everything looks easy when someone else does it, no parts left over no parts missing no springs flying across the room. The full diameter portion is too short, and the spring spike is too long. This is the only step requiring the use of a tool (punch, small screwdriver, Allen wrench, etc... ). Once you're sure the weapon is safe, you can leave the action open. Yup, the first time is not pleasant. Three word come to mind when I think about taking mine apart for the first time: A Fu@king Pain in the Ass. The shotgun is now clear and it is safe to begin disassembly. On my gun it reduced the mag capacity by one round!

Mossberg 500 Magazine Tube Removal Company

This pin holds the bolt in place. Push the forearm forward. I removed the tube on my '60's vintage Mossberg 500 20 gauge. Then, clean the outside of the barrel with a damp cloth. Quote: I tried to lube it with break-free and Kroil for several days and the situation did not get any better. Tip: If the forearm has not been moved the bolt slide should be lined up correctly for easy removal. Either one is at best a $150 shotgun so it's not like we are risking the farm on the conversion... I have stripped the weaon and used every type of clamping device I have and the tube is threaded so tightly that I cannot get it to budge. You can use a punch or screwdriver. D. Physically and visually check the chamber and elevator to ensure there are no shotshells present, then move the forearm forward and close the action. Finally, wipe down the stock and forend assembly with a damp cloth. Unscrew (counter-clockwise) the takedown screw. Next, slide the forend assembly forward and off the receiver. You may have to fully or partially close the action while doing this.

Mossberg 500 Magazine Plug Removal

The rear of the trigger guard can then be pulled downward and out of the receiver. I also installed a Vang Comp oversized safety and I am impressed with the quality of that part. Move the action rearward until the Bolt Slide lines up with the receiver's clearance cut, highlighted in yellow. Remove the shell stops (not sure of the technical term, they are the bottom two bars that fall out when you remove the trigger group). With the screws loosened, the stock can now be slid off the receiver. To disassemble your Mossberg 500 shotgun, first remove the magazine cap and unscrew the barrel from the receiver. Start by cleaning the bore of the barrel with a bore brush and solvent. Step 4: Remove the Cartridge Stop and the Cartridge Interrupter. Remove the trigger group by depressing the release lever in front of the trigger guard and then pulling the trigger group straight out.

Mossberg 500 Magazine Tube Removal Instructions

The title says it all, if you've done it mind telling how tough it was? Once the stock is removed, you will see two screws on the back of the receiver. First, make sure the gun is unloaded. Use a pair of vice-grips with padded jaws (or heavily tape wrapped jaws), and clamp them to the farthest end of the magazine tube. Then, remove the magazine cap and slide the forend assembly forward. Don't turn from the top of the receiver, turn from the bottom close to the mag tube. Be careful when removing the bolt as the bolt spring is under tension and can cause the bolt to fly out of the receiver. Once you have the gun back together, you can now clean it. Thread Tools||Display Modes|. All that happened was the threaded insert at the end spun. I didn't heat mine for fear of melting the follower but it came off eventually.

Mossberg 500 Magazine Tube Removal Services

I agree, if the military doesn't feel the need for it I doubt I would reapply it. And it doesn't bind like the Choate did from time to time. I ordered a new spring and figured it would be no trouble to change out.

The next step is to remove the trigger assembly. With the cap removed, you should be able to see the magazine spring and follower. The first step is to make sure the shotgun is unloaded. E. Reach into the loading port underneath the gun, and push on the cartridge stop in the left sidewall of the gun with your right thumb. Use your finger to push the bolt forward and out of the circular hole where the barrel used to be. But now I can't get the damned trigger assembly back in--ive been trying for like an hour and a half. Check to make sure the barrel and mag tube are empty. DO NOT PULL THE TRIGGER! To do this, unscrew the magazine cap clockwise. These instructions break the shotgun down into 10 parts. That tube is stuck tight. Been using them for years and swear by them). Using slight thumb pressure on the base of the shotshell to help it clear the elevator, pull it free from the magazine and out the loading port on the bottom of the gun. Unscrew and remove barrel.

It is generally recommended that you clean your shotgun after every use. There is more than one red Loctite. Clamp the receiver in a vise between two pieces of wood and use a strap wrench. From the factory, the mag tubes are attached with a large amount of loctite.