Are All O2 Sensors The Same Thread Size For 1

Drive Size (in): 3/8 Inch. Be back and let you know. As a registered member, you'll be able to: - Participate in all Tacoma discussion topics. I took my sensor back to the shop and ran a guide on it, im not sure what the correct terminology is in english (the factory is russian and all the parts names i learned were in russian) but u use it to make bolts with threads such as the one on the o2 that i was trying to replace. 02-12-2010, 09:08 AM #6. The nuts holding the cat on are completely deteriorated and the gaskets are too. This product is universal and applies to all vehicles. You could always borrow one? I'd take a picture of the threads, but none that I take seem to come out real well. O2 Sensor Size and Thread Pitch. Hello, I recently picked up a set of V&H Short Shot pipes for my 07 Street Bob. "Sometimes a concept is baffling not because it is profound, but because it is wrong.

• Are all o2 sensors the same thread size matters
• Are all o2 sensors the same thread size for 20
• Are all o2 sensors the same size
• What size is o2 sensor threads

Are All O2 Sensors The Same Thread Size Matters

"In like a gentleman, out like an animal"-Juan Montoya on driving @ Martinsville. I got a spark plug tap from NAPA, KD tools number 730 for only 8$. Yep, I guess having the bung replaced would be just as good and likely quicker, though I doubt the $26 cost of the shipped tap is higher than the welding labor and bung, plus I'll be prepared if I hit it again (hope not). Are all o2 sensors the same thread size for 20. Share your knowledge of this product. I don't care what you say, my anecdotal evidence agrees with my reality. Cheapest I could find: # 20.

Are All O2 Sensors The Same Thread Size For 20

In the mean time, the car's dead! Sunny Manzanillo, Mexico. I am shopping on Amazon because of cheaper prices + quick shipping and I am finding alot of "universal" items that are thread sizes of "M18*1. If you've ever replaced an oxygen sensor yourself you know how crusty and corroded the threads on the exhaust pipes can get! Representative Image.

Are All O2 Sensors The Same Size

Location: San Francisco, CA. I can't tell you the exact spec, but measured the OD of the threads and they are 17. Product Information. Oxygen sensor thread pitch/compatibility. - Old Gen.: 80's GL/DL/XT/Loyales. Product Description. Afterward, use an O2 sensor socket wrench to break loose the O2 sensor. If you remove or disable your O2 sensor, you will not pass state vehicle emissions testing, as this modification is routinely used by those using their vehicles for off-road or track racing purposes.

What Size Is O2 Sensor Threads

Enter your email address for special offers from PLX Devices Inc. © Copyright 2015, PLX Devices Inc. All Rights Reserved. The thread was redone and the sensor went in flush. Went to 3 different local auto parts stores, and the largest they go is 12m 1. But, it works and fits great. The connector is conveniently located under the carpet under the driver's seat. It's likely that you'd need an entire metric tap&die set. Are there other sizes? OXY sensor thread size. I've spent the last 3 hours trying to re-thread the hole for the upstream sensor on the cat but I just can't do it. Insert it into the exhaust system and connect it to the electrical wiring. Weld In Oxygen Sensor Bung Fitting M18 x 1.5mm. 5 pitch thread chaser is the correct size for all Bosch oxygen sensors used in Volvos. A universal one is just taht, each side has thread measurements on it, it's 4 sided with 2 ends on it so you should get 8 different threads. Detailed Description. Its steel alloy makes it easy to weld.

Location: Watts Bar Lake. 31st July 2013, 21:09||# 3|. Plug Gappers & Feeler Gauges. Users Browsing this Thread. Join Date: Sep 2003. 25 thread pitch bolt fits perfectly.